Just how to Replace a Bath Tub ( Guide).
Just how to Replace a Bath Tub ( Guide).
Blog Article
We've noticed the article on Tools You Need to Install a New Bathtub down the page on the internet and figured it made sense to discuss it with you on my blog.
Installing a tub isn't precisely rocket science, however it does call for strong plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is easily easily accessible, the task can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the new one. Ensure you have qualified on your own for the task as well as are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed project, it is better to consider employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your restroom if you have already acquired a brand-new tub and don't require to alter the plan of your previous water system pipes.
Your tools and also product checklist ought to comprise the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The process of getting rid of the existing taps can be quite troublesome because of the restricted accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, position the bath tub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level checks out degree.
To set up faucets, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the supply of water and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bathtub has actually been utilized at least when as this will settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washers are in area between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads on A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece was essential. Enjoyed our entry? Please share it. Let others check it out. Bless you for your time. Don't hesitate to visit our site back soon.
Book 24/7 Report this page